Roam owner support

A little help, when you need it.

Practical guides for your hub, sensors, and alerts. Just unboxed your Roam? Start with the setup guide.

The app and your account

Use the same Roam account on your phone and in the web app. Local setup requires the mobile app and a nearby hub.

Adding a boat

Choose Add a Boat, scan or enter the hub’s setup code, and save your boat details. For a six-digit serial number, choose Have an older Roam hub? instead. See the registration steps.

Your boat is missing

Check that you signed in with the email used to register the hub or receive its invitation. If someone else owns the boat’s account, ask them to check your invitation. Contact support if it is still missing; avoid creating another account to try to recover it.

Cellular, Wi-Fi, and local connections

These connections do different jobs:

  • Cellular connects the hub to Roam when you are away from dock Wi-Fi. It needs coverage and a plan that includes cellular.
  • Wi-Fi connects a newer Roam Hub to the internet through a network you configure. Monitoring over Wi-Fi depends on that network remaining available.
  • A local wireless connection connects your phone to a nearby hub for setup. Compatible wireless sensors also communicate directly with the hub. Your phone’s local connection is not a replacement for the hub’s internet connection.

Connect your hub to Wi-Fi

  1. Stand near your powered hub and allow the app to connect to nearby devices.
  2. In the Roam mobile app, open your boat’s Device Settings and choose the local connection option.
  3. Use the Wi-Fi controls to choose your network and enter its password.
  4. Check for a fresh dashboard reading after connecting.

Older Roam hubs are cellular-only. Compare current plans for the newer hub.

Understand the last update time

A displayed value may be the last reading the hub sent. Check its update time before treating it as current. When the hub has no internet connection, new readings and remote alerts cannot reach your phone until it reconnects.

Add a wired sensor

Use the installation instructions for your particular hub and cable. On the newer Roam Hub, IN1 is voltage-only; IN2–IN4 support voltage or switch sensors. Do not use the older hub’s numbered-port instructions to wire a newer hub.

  1. Install the compatible cable or sensor and note the labeled input it uses.
  2. Open Add Wired Sensor in the app.
  3. Select the same input and the appropriate type, such as Voltage, Bilge Pump, Float Switch, or Shore Power.
  4. Give the sensor a useful location name and configure its alarm settings.
  5. Save, then check the displayed reading or state against the actual sensor.

A battery reading should be plausible for that battery. A float or door switch should change state when safely operated. If the reading is wrong, check the selected input and sensor type before changing alarm thresholds.

Shore power must use a compatible shore-power sensor. Never connect AC power directly to the hub. Do not interrupt a working bilge pump’s power or automatic control to test a monitoring sensor.

Add a wireless sensor

  1. Power the sensor and start with it close to the hub. Keep your phone nearby and allow the app to connect to nearby devices.
  2. Open Wireless Sensors → Add External Device.
  3. Choose the matching sensor family and follow its prompts to scan or enter the required device details.
  4. Name the sensor for its location and check that a reading arrives.
  5. Move it to its intended location and check again. Metal compartments and distance can reduce wireless range.

For compatible Victron devices, follow the app’s instructions for the device’s broadcast settings and encryption key. Those details are different from your Roam hub’s setup code.

If a sensor is not found, check its battery or power, move it closer, confirm the selected family, and scan again. Review your plan if the app shows a feature restriction.

Set up and check your alerts

Seeing a sensor on the dashboard does not mean its alarm is configured. Review the settings for each sensor you want Roam to watch.

  1. Enable the relevant high, low, or triggered alarm and save it. Use thresholds appropriate for your boat; battery types and normal operating conditions vary.
  2. Enable notifications for Roam in your phone’s system settings.
  3. Check whether the alarm is muted or Mute While Aboard is enabled.
  4. Safely exercise the sensor, confirm that the app sees the change, and check that the expected notification reaches your phone.
  5. Restore normal conditions and any settings you changed for the test.

Phone Focus / Do Not Disturb settings can affect how notifications appear. Check those settings if an alert reaches the app but you do not hear or see it on the phone.

Remote alerts need a working internet connection from the hub and an available delivery path to you. Check your readings and connection before leaving the boat.

Something not working?

The setup code will not register

Check your phone’s internet connection and enter the code exactly as printed. An older hub’s six-digit serial belongs in Have an older Roam hub?, not the setup-code field. If the hub may already belong to an account, contact support rather than repeatedly registering it.

The app cannot connect to my nearby hub

Check the hub has power, move closer, and allow Roam to connect to nearby devices in your phone’s permissions. Try the local connection option in Device Settings again. The newer hub’s local setup instructions do not apply to older hubs.

My hub is offline or readings are old

Check the last update time, hub power, and the internet connection it uses. For cellular, review coverage and your plan. For Wi-Fi, check the network still has internet access and whether its password changed. If a local connection works but remote readings do not, report that distinction to support.

One sensor is missing or shows the wrong reading

If other sensors update normally, check the affected sensor’s power and setup. For wired sensors, verify the input number and type. For wireless sensors, move it near the hub and check its battery. Note the last successful reading and any recent changes.

I can see readings, but I am not getting alerts

Confirm the alarm is enabled and its trigger condition actually occurred. Check muted alarms, Mute While Aboard, phone notification permissions, and Focus / Do Not Disturb. Follow the alert checklist and safely retest.

Get help from Roam

Send a message to support. Include:

  • Your account email, boat name, and hub model or serial number.
  • What you expected and what happened, including the exact error message.
  • The last update time, any hub light behavior, and what you have already tried.
  • Your phone model and whether you are using iOS, Android, or the web app.

A screenshot or wiring photo can help. Do not include passwords, setup codes, or sensor encryption keys.